Golvolja

Floor Oil

Drying oil for treating and polishing parquet and wood floors. Contains no solvents.

Available in 1 litre and 5 litre tin canisters, 200 litre drums and 1000 litre IBC containers. Where to buy.

FLOOR OIL is linseed oil from which the non-drying ingredients have been removed with our unique refining method. It penetrates the substrate and dries quickly by a reaction with the oxygen in the air to linoxyn, a natural polymer with excellent adhesion. It is non-biodegradable, water-repellent and resistant to fats, petroleum products, salts and household acids, e.g. lemon, wine and vinegar.
At 20 °C / 60 °F and with good ventilation, FLOOR OIL dries in 24 hours or less. Read more on the TECHNOLOGY.

FLOOR OIL is absorbed 1.5-3 mm (roughly 1.5-3/250 of 1”) into the wooden floor, and produces a deep lustre that cannot be achieved using waxes or synthetic oils, which do not penetrate the surface.
Therefore the treatment is permanent until the impregnated wood layer has been worn down, which usually takes decades.

Damage to the surface is easily fixed by grinding off the damaged wood and then polishing that area with FLOOR OIL.
After years of wear, shiny streaks may appear on floors. These can easily be revived by polishing with a cloth or  a polishing pad and a small amount of FLOOR OIL.

Download the work manual in PDF here or read it below.
The Technical Data Sheet and the Safety Data Sheet are under the heading Datasheets in the main menu.

WORK MANUAL

Note that birch and beechwood becomes mottled when oiled and thus a good oiled surface is difficult to achieve. This is because these woods absorb lots of oil, and the colour of the wood varies, particularly on different grains of the lamellas.

Sand the floor with an abrasive pad, #180 or finer - a coarser sheet creates marks that the oil cannot fill when absorbed by the wood.

Heat the FLOOR OIL to 130 °C / 266 °F in a deep fryer.

Apply a good amount of FLOOR OIL using a natural bristle brush. Spread from saturated areas to areas still absorbing oil. Apply and spread until the entire area is saturated and a thin layer of oil remains on the surface.

FLOOR OIL at 130 °C / 266 °F is as thin liquid las water. When you apply warm FLOOR OIL, moisture in the wood evaporates, bordered pits open outwards due to the vapour pressure in the cells, and the warm FLOOR OIL penetrates. You can see small steam bubbles on the surface when you apply warm FLOOR OIL.

You can safely work with 130 °C / 266 °F FLOOR OIL - it will neither burn nor fume. Its boiling point is 300 °C / 572 °F, and it will start to exude a white, sharply smelling steam from its surface at 180 °C / 356 °F. At 130 °C / 266 °F, it will only produce a faint smell of linseed oil.

Let the oil be absorbed - for half an hour to one and a half hours.

Sand in the oil using a #240-320 abrasive sheet on a single disc scrubbing machine. The resulting oil-saturated dust fills the roughness of the wood surface and makes it even and smooth.

Remove all remaining oil and dust left on the surface after 20-30 minutes. Oil left on the surface will leave a sticky skin. If that happens, gently use a card scraper to remove the skin and then machine-polish with FLOOR OIL.

Wash brushes, tools and utensils with strong soft soap before the oil dries.
Video: Washing brushes with Selder´s STRONG SOFT SOAP.

Allow time to oxidize: the oil dries by oxidation and the time needed to dry is dependent on two factors: the supply of oxygen and the temperature. The oil can dry to the touch in a few hours’ time on a windy, hot summer day, whereas it can take up to a week in a cool, poorly ventilated garage.

Polish to the desired sheen - from matte to high gloss - using a single-disc scrubbing machine and an abrasive sheet or polishing pad and some oil. A #220 abrasive pad produces a silk-matte result whereas a #1000-#5000 polishing pad will produce a semi- to high gloss result #100 coarseness slip protection. Keep the surface moist by wetting the abrasive sheet or polishing pad with FLOOR OIL. Repeat until the entire surface has an even sheen.

Note: do NOT polish too large surfaces at a time if you use Selder & Co’s LINSEED VARNISH OIL. With a floor at room temperature or warmer, the oil will dry before you’re finished working.

Wash brushes and tools used with a strong soft soap, e.g. STRONG SOFT SOAP.

WORKER SAFETY

No respiratory protection necessary. Provide good ventilation. The oil is a poor heat conductor and does not cause burns if spilled, but be aware that metal objects that have been in contact with warm oil burns.

WARNING: DANGER OF SPONTANEOUS COMBUSTION!

Cloths and other porous materials moistened with linseed oil must be soaked in water without delay before disposal. Oil-treated surfaces do not ignite on their own. The danger concerns only fibrous materials.

Metal objects that have been in warm oil burns.